The influence of planting density on the oil and fatty acids content of soybean in hydroponic and soil conditions of the Ararat Valley
DOI:
https://doi.org/10.31989/bchd.v7i9.1441Abstract
Background: Plant seed oils are major renewable resources from nature that can be used in multiple applications. Oils and fats are a vital component of human diets. About 1/3 of the daily energy requirements of a healthy diet come from fats. Each branch of the food industry has its own demands for the fatty acid composition of seed oils. High amounts of polyunsaturated fatty acids are a requirement of healthy diets. However, food manufacturers need highly saturated fatty acids because they need oil that is resistant to high temperatures and oxidation. Soybean oil is second only behind palm oil as the most commercially abundant plant oil globally. Soybean has been recognized for its agricultural importance and their various positive effects on human health.
Objective: to identify the quantitative changes of soybean fatty acids depending on the planting density and growing conditions in the Ararat Valley of Armenia.
Methods: Soybean was grown in hydroponic and soil conditions of the Ararat Valley. The seeds were sown in the middle of April. Experiments were carried out in hydroponic equipment and soil with different planting densities (30, 50, 70 and 90 plants/m2). The oil content was measured by using the pulsed nuclear magnetic resonance method. The composition of fatty acids in seed oil was analyzed by chromatographic method on "Chromatec Crystal 5000" GC.
Results: Oil content ranged from 19.6% to 24.4% in all variants. The maximum content was registered in soil with 30 plant/m2 planting density. Linoleic acid content ranged from 46.35 to 51.28% of the total fatty acid content, regardless of planting density and growing media. The content of linolenic acid ranged from 4.13 to 5.11% in all variants. The maximum content of ω-3 and the minimal content of ω-9 was recorded in hydroponics at 30 plants/m2 planting density. The highest percentage of stearic acid was observed in the soil variant with a planting density of 30 plants/m2. Interestingly, the variants did not differ in the total content of the 5 main fatty acids (98.84-98.95%). Growing medium had no significant effect on the total saturated fatty acids content; in all variants it ranged from 14.29% to 14.83%. Total unsaturated fatty acids content ranged from 85.2% to 85.7%. The hydroponic variant with a planting density of 30 plants/m2 had the lowest ratio of ω-6 and ω-3 fatty acids (10:1).
Conclusion: Planting density and growing media had a significant influence on the content of monounsaturated and polyunsaturated fatty acids. Under hydroponic conditions the lowest content of monounsaturated and the highest content of polyunsaturated fatty acids were observed at the lowest planting density (30 plants/m2), which can be used as a functional food for daily consumption.
Keywords: Glycine max (L.) Merr., soilless culture, ω-3, ω-6, ω-9, saturated acids.
Downloads
Published
Issue
Section
License
Copyright (c) 2024 FFC/Bioactive Compounds in Health and Disease
This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.
Any manuscripts or substantial parts of it, submitted to the journal must not be under consideration by or previously published in any other journal or citable form. Authors are required to ensure that no material submitted as part of a manuscript infringes existing copyrights or the rights of a third party. In submitting one's article in any form, the author has assigned the FFC publishing rights and has agreed to an automatic transfer of the copyright to the publisher. This is so that the FFC may create print option journals, for example, at the FFC’s discretion. If the author wishes to distribute their works by means outside of the FFC, for example within their community, they will have to place a request.
Correspondence concerning articles published in Functional Foods in Health and Disease is encouraged. While derivative works (adaptations, extensions on the current work, etc.) are allowed, distribution of the modified material is not allowed without permission from the FFC.